层次分析法在致密油有利区优选中的应用——以川中侏罗系大安寨段为例   总被引：1，自引：0，他引：1  

Wang Shaoyong  Li Jianzhong  Guo Qiulin  Li Denghua 《地球科学进展》2015,30(6):715-723

层次分析法常用于解决复杂系统分析与决策中目标优选、排序等问题,也适用于油气勘探领域。在前人致密油地质特征研究的基础上,总结了致密油有利区优选指标。使用层次分析法优选有利区的核心内容是建立层次结构模型和构建2类矩阵。以四川盆地中部侏罗系大安寨段为例,介绍了使用层次分析法优选有利区5个主要步骤:1根据研究区地质特征,确定目标及方案,构建目标层和方案层;2根据影响致密油富集的要素,确定准则层;3构建准则层中各要素的成对比较矩阵,确定各准则要素的相对权重;4构建各准则要素对不同方案的判断矩阵,确定不同方案中各准则要素的权重;5将不同方案各准则要素的权重矩阵与准则要素的相对权重矩阵相乘,得到各方案的层次排序,进而选出最佳方案。优选的川中侏罗系大安寨段致密油最有利勘探区为金华—莲池区。操作简单、不需考虑下限值、适用范围广是层次分析法优选有利区的优点,但由于层次分析中的标度根据人为经验赋值,不同评价人员给出的评价结果有所不同。将层次分析法与GIS、特尔菲法、模糊数学法相结合,可以提高准则要素的优选合理性及赋值准确性。  相似文献   

热处理砂岩微观结构及力学性质试验研究     

赵怡晴  吴常贵  金爱兵  孙浩 《岩土力学》2020,41(7):2233-2240

采用核磁共振、电镜扫描、X射线衍射、单轴压缩等试验手段对某砂岩试样不同温度下（25～900 ℃）微观结构及力学性质的变化情况进行研究。研究表明：温度对砂岩试样微观结构具有重要影响，试样总孔隙率随温度的升高而升高，在150 ℃以下，由于中、大孔隙的减少，试样渗透性反而降低；当温度超过600 ℃时，中、大孔隙快速增加，试样渗透性能大幅增加；温度升高导致砂岩试样弹性模量减小、峰值应变增大以及孔隙压密阶段变长，宏观表现为脆性降低、塑性明显增强；热处理条件下，除微观结构的变化会导致砂岩试样力学强度改变外，试样矿物成分对其力学强度也具有十分重要的影响；450 ℃以下，由于矿物成分变化较小，试样力学强度主要受到孔隙度增加的影响，表现为强度随温度升高而降低；450～600 ℃，虽然孔隙率继续增长，但由于主要矿物高岭石发生脱水以及与其他离子形成新相矿物，进而导致试样强度没有随着孔隙增加而降低，反而出现一定的增长；超过600 ℃后，孔隙尤其是大孔隙的急剧增加，导致强度重新开始降低。  相似文献   

Effects of fluid displacement pattern on complex electrical impedance in Berea sandstone over frequency range 104–106 Hz          下载免费PDF全文

Yi Zhang  Hyuck Park  Osamu Nishizawa  Tamotsu Kiyama  Yu Liu  Kwangseok Chae  Ziqiu Xue 《Geophysical Prospecting》2017,65(4):1053-1070

To better understand the effect of fluid distribution on the electric response of rocks saturated with oil and brine, we conducted experimental studies on the complex electrical impedance in a Berea sandstone, together with in situ acquisitions of oil distribution images employing a high‐resolution medical X‐ray computed tomography. We performed two tests of brine displacement by oil under high (10 MPa) and low (5 MPa) pressures, which were accompanied by fingering and stable displacement patterns, respectively. The measured complex impedance data were fitted to the Cole model to obtain the resistance, capacitance, peak frequency of the imaginary impedance, and the exponent α of the rock–fluid system. With increasing oil saturation, the resistance showed an increasing trend, whereas the other three parameters decreased. The fingering displacement exhibited lower resistance and capacitance than the stable displacement. The analysis of the resistance changes using a simple parallel connection model indicates that there are more components of residual brine in parallel connections in the fingering pattern than in the stable displacement pattern at the same saturation. We also interpreted the normalised changes in the capacitance (or apparent dielectric constant) with respect to the oil saturation via an analysis of the shape factor of fluid distribution based on the Maxwell–Wagner–Brugermann–Hanai model. The changes in the shape factor suggest that the pinch‐off of the brine in parallel connection by the oil is a dominant mechanism reducing the capacitance. In the stable displacement, most of the connections in the brine phase are immediately pinched off by oil displacement front at a local oil saturation of 65%. Conversely, in the fingering displacement, there is a transition from the bulk or layered brine to the pinched‐off at a local oil saturation below 60%. The analyses indicate that the difference in the fluid distribution under different fluid conditions is responsible for the non‐Archie behaviour.  相似文献   

Characterisation and multifaceted anisotropy assessment of Corvio sandstone for geological CO2 storage studies          下载免费PDF全文

Ismael Falcon‐Suarez  Jacobo Canal‐Vila  Jordi Delgado‐Martin  Laurence North  Angus Best 《Geophysical Prospecting》2017,65(5):1293-1311

We present a comprehensive characterisation of the physical, mineralogical, geomechanical, geophysical, and hydrodynamic properties of Corvio sandstone. This information, together with a detailed assessment of anisotropy, is needed to establish Corvio sandstone as a useful laboratory rock‐testing standard for well‐constrained studies of thermo–hydro–mechanical–chemical coupled phenomena associated with CO₂ storage practices and for geological reservoir studies in general. More than 200 core plugs of Corvio sandstone (38.1 and 50 mm diameters, 2:1 length‐to‐diameter ratio) were used in this characterisation study, with a rock porosity of 21.7 ± 1.2%, dry density 2036 ± 32 kg m^?3, and unconfined compressive and tensile strengths of 41 ± 3.28 and 2.3 ± 0.14 MPa, respectively. Geomechanical tests show that the rock behaves elastically between ～10 and ～18 MPa under unconfined conditions with associated Young's modulus and Poisson's ratio of 11.8 ± 2.8 GPa and 0.34 ± 0.01 GPa, respectively. Permeability abruptly decreases with confining pressure up to ～10 MPa and then stabilises at ～1 mD. Ultrasonic P‐ and S‐wave velocities vary from about 2.8–3.8 km s^?1 and 1.5–2.4 km s^?1, respectively, over confining and differential pressures between 0.1 and 35 MPa, allowing derivation of associated dynamic elastic moduli. Anisotropy was investigated using oriented core plugs for electrical resistivity, elastic wave velocity and attenuation, permeability, and tracer injection tests. Corvio sandstone shows weak transverse isotropy (symmetry axis normal to bedding) of <10% for velocity and <20% for attenuation.  相似文献   

Borehole failure analysis in a sandstone under anisotropic stresses     

Euripides Papamichos 《国际地质力学数值与分析法杂志》2010,34(6):581-603

Borehole failure under anisotropic stresses in a sandstone is analyze numerically for various borehole sizes using a nonlinear elastic–plastic constitutive model for a Cosserat continuum. Borehole failure is identified as macroscopic failure of the borehole through the development of shear bands and breakouts. The results compare well both qualitatively and quantitatively with experimental results from polyaxial tests on Red Wildmoor sandstone. They show that the hole size effect of the borehole failure strength is independent of the far‐field stress anisotropy and follows a ? power law of the hole size. A similar scale effect equation with a ? power law is proposed for the scale effect of the maximum plastic shear strain at failure. This equation can be useful for better predicting hole‐size‐dependent failure with standard codes based on classical continua. The effect of stress anisotropy on the borehole failure stress is found to be independent of the hole size. The failure stress decreases linearly to 40% as the stress anisotropy increases. However, the maximum plastic shear strain at failure is stress anisotropy independent and therefore the critical plastic shear strain for failure is only hole‐size dependent. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

哈拉哈塘地区东河砂岩段-角砾岩段沉积模式探讨     

徐正华  马青  徐大宝  邬兰  徐智  杨春梅 《海洋地质译丛》2010,(1):26-30

塔北的哈拉哈塘地区是东河砂岩油气勘探的重点地区，该地区目前已发现并探明了东河塘和哈得4两个东河砂岩油气藏，油气储量丰富，显示出良好的勘探前景。基于哈拉哈塘地区东河砂岩段和角砾岩段的岩性段穿时沉积现象异常明显，根据层序地层学原理和方法对哈拉哈塘地区东河砂岩段一角砾岩段进行了重新分层和对比，在层序分层等时地层框架的基础上重新进行了东河砂岩段一角砾岩段沉积模式研究，弄清该地区地层分布规律、演化规律、砂体分布及储层分布规律对该地区的油气勘探具有重要指导意义。  相似文献   

Reprint of: Diagenetic controls on evolution of porosity and permeability in lower Tertiary Wilcox sandstones from shallow to ultradeep (200–6700 m) burial,Gulf of Mexico Basin,U.S.A.     

Shirley P. Dutton  Robert G. Loucks 《Marine and Petroleum Geology》2010

Reservoir quality is a critical risk factor in deep to ultradeep reservoirs at depths >4.5 km. Analysis of Paleogene Wilcox sandstones on the upper Texas Gulf Coast provides insight into the evolution of reservoir quality during shallow to ultradeep burial diagenesis. Reduction of porosity and permeability with burial in Wilcox sandstones was evaluated using subsurface samples from 200 to 6700 m, at temperatures of 25–230 °C. Diagenesis and petrophysical properties were interpreted from petrographic data and core analyses. Wilcox sandstones are mostly lithic arkoses and feldspathic litharenites having an average composition of Q₅₉F₂₂R₁₉. Provenance did not change significantly during Wilcox deposition in this area, nor does average sandstone composition vary among lower, middle, and upper Wilcox sandstones. However, composition does vary with sequence-stratigraphic position; lowstand slope-fan deposits contain more rock fragments than do deposits from highstand or transgressive systems tracts. Given observations from this onshore dataset, Wilcox sandstones deposited in deepwater environments in the Gulf of Mexico are likely to contain more rock fragments than their linked highstand equivalents.  相似文献   

西湖凹陷西次凹古近系花港组—平湖组深层油气成藏过程          下载免费PDF全文

刘春锋  蒋一鸣  李宁  郭小波  马剑  张武  熊志武 《地质学报》2024,98(1):231-246

西湖凹陷西次凹古近系花港组和平湖组深层油气资源丰富，是东海陆架盆地勘探开发新领域，受储层差异致密化影响，油气成藏机理复杂。为了厘清西次凹深层油气成藏过程，本文通过流体包裹体岩相学特征、显微测温、激光拉曼光谱、包裹体所含油气地球化学等实验分析，结合构造演化、地层埋藏史、热史等，开展了系统的储层特征、油气成藏期次、成藏过程研究。结果表明，花港组深层（>4000 m）和平湖组储层均已致密化，溶蚀孔隙是主要的储集孔隙类型；花港组和平湖组均发育两期油气包裹体，早期含油包裹体较多，晚期以天然气包裹体为主，成藏时间分别为龙井运动期和冲绳运动期，以晚期天然气成藏最为关键。包裹体中油气地球化学特征类似，反映生烃母质以高等植物生源为主，低等生物为辅，与平湖组煤系烃源岩特征一致。冲绳运动叠加平湖组生气增压是晚期天然气成藏的主要动力，此时H10段及以上储层未致密化。根据储层致密化与成藏时序匹配关系可将西次凹M构造深层油气藏类型划分为常规型、先成藏后致密型、先致密后成藏型和边成藏边致密型4种。本文成果可为研究区下一步致密砂岩气的勘探开发部署提供重要的理论依据。  相似文献   

鄂尔多斯盆地镇北地区长3储层微观非均质性的实验分析   总被引：10，自引：0，他引：10  

刘林玉  张龙  王震亮  高潮 《沉积学报》2007,25(2):224-229

油气储层的微观非均质性特征是储层地质学研究的重要内容之一。本文的目的是研究鄂尔多斯盆地镇北地区长3储层微观非均质性特征,研究方法是利用真实砂岩微观模型实验。通过实验发现鄂尔多斯盆地镇北地区长3和储层为致密型砂岩,真实砂岩微观模型实验直观地显示出鄂尔多斯盆地镇北地区长3储层具有很强的微观非均质性,砂岩的成岩作用和孔隙结构是影响本区长3储层微观非均质性的主要原因。在低渗透砂岩中,溶蚀作用引起砂岩产生强烈的非均质性,而这些砂岩则形成长3储层的高渗带。  相似文献   

塔里木陆块西北缘萨热克砂岩型铜矿床构造-流体演化对成矿的制约     

王伟  李文渊  高满新  熊中乙  李天虎  宿晓虹  郭周平  孟勇  全守村  刘增仁  叶雷  陈传庆  唐小东 《地质通报》2018,37(7):1315-1324

塔里木陆块西北缘萨热克砂岩型铜矿床构造演化、流体演化与成矿之间具有密切关系,处于一个统一系统中。矿床成岩期方解石中包裹体水的δD值为-65.3‰~-99.2‰,改造成矿期石英包裹体水的δD值为-77.7‰~-96.3‰,成岩成矿期成矿流体δ~(18)OH_2O变化范围为-3.22‰~1.84‰,改造成矿期成矿流体δ~(18)OH_2O变化范围为-4.26‰~5.14‰,指示萨热克铜矿成岩期、改造期成矿流体主要为中生代大气降水及其经水岩作用而成的盆地卤水。矿石中辉铜矿δ~(34)S值为-24.7‰~-15.4‰,指示硫主要源自硫酸盐细菌与有机质还原,部分源于有机硫。构造与成矿流体演化对砂岩铜矿成矿起关键制约作用。盆地发展早期强烈的抬升运动使盆地周缘基底与古生界剥蚀,为富铜矿源层的形成提供了丰富物源,至晚侏罗世盆地发展晚期,长期演化积聚的巨量含矿流体在库孜贡苏组砾岩胶结物及裂隙中富集,在萨热克巴依盆地内形成具有经济意义的砂岩型铜矿床。  相似文献